Plumbing problem

I have two embarrassing things to write about today.  The first is the length of time since an update on what's happening with the house.  Yeah, it's been awhile.  I'm not going to dwell on that, though.  The other embarrassing thing is related to the first, though: A few months (more than 2, less than 3) ago, I heard a drip under my bathroom vanity.  I just now (last weekend) got around to fixing it.  Now you know my shameful secret.  :-)

The drip wasn't from the faucet, it was from the drain.  I had repaired a poor install in the kitchen last winter(?), and I'm starting to suspect the previous owners weren't the best plumbers.  When I looked at where the drip was coming from, it seemed to be coming from right at the drain in the sink itself, so I suspected that the plumber's putty used to seat and seal the drain had failed.  When I actually undid the drain, I found out it was a bit worse:

From Plumbing problem

Looking at the pieces I also notice that it didn't seem that whoever installed it had used any teflon tape on the threads, either.  I doubt that alone caused it to fail, but I suspect that the threads were over-tightened which caused the part to crack and fail.

So, I went back to the hardware store and got a replacement part, which was identical to what I had taken out:

From Plumbing problem

There wasn't a whole lot to getting it back into position and reconnecting the trap and the drain plug mechanism. I did notice that I think the trap part was not exactly under the drain plug assembly.  The additional stress that the part may be under might cause it to fail again sooner than it should, although I have my fingers crossed that it will last longer than the previous part.

If it does fail again prematurely, I'm going to add a flexible pipe section between the replacement assembly and the trap.  I'm starting to believe that DIY plumbers that don't measure accurately should use at least one flexible fitting in the plumbing to relieve stresses on the glue joints.  Only time will tell if my fix was good this time around.   

Shower door project

This is what my shower has looked like for the past 3 weeks or so, ever since Renae discovered that water from the shower was leaking into the basement.

I had taken the door off of the frame when I was tracking down the leak.  I had assumed that the door was improperly hung and that a simple adjustment would take care of water that was getting under the bottom of the door.

After talking to one of the employees in the Bath department at Lowe's, I learned that actually the door had been installed correctly. The real problem was that the door was not the right type of door to use in that shower.  The shower head is opposite the door, and the pivot style door is designed to be used with a shower having the shower head on a side wall.

Because the pivot style doors are prone to letting water get through and there was going to be little hope of fashioning a decent fix, we decided to order a new door.  We had always planned on replacing this shower door, since the door frame has a horizontal bar that you have to duck under going in and out of the shower. We thought it was going to be a project a few years down the road, though. But two weeks after placing the order, I had the new door in the back of the car.

Getting the frame off was pretty easy. I pulled the screws holding it together and gently pried the frame away from the tile. The silicone caulk held it pretty tightly in place, but I was able to get it off without scratching the tile.

The bottom part of the frame had about half a tube of caulk which was still wet underneath it!  I took a photo of it:

I guess whoever installed it just squirted a ton of caulk through the pivot hole and figured it would dry eventually. Not so much, in this case. It does explain why there was a thin sheet of dry silicone covering the entire part of the inner door ledge, however. 

Four hours later, and I have my new door installed:

Really it only took about an hour of measuring, drilling, leveling and fastening.  The other three hours were spent going back down to the workshop to hunt down a tool I didn't think I would need, but found that I really did need.

Here's what I learned doing this project:

• Get all the tools that the instructions call for.
• Read the instructions twice before starting the project.  I read through them once and it didn't make any sense.  The second time through I started figuring it out.  (Actually, reading the instructions is the number one thing that I've learned from every contractor I've ever worked with.)
• Covering the drain with a towel like Rich on "This Old House" does is a smart idea(r). 
• Use the proper drill bit for the material you are drilling through.  I used a masonry bit to get through the tile. The previous homeowner (probably) did not and ended up chipping the tile up pretty good.  I tried to hang the door to cover the old holes as much as possible, but ended up sacrificing a bit of evenness from one side to the other to cover some of the holes. Not content to learn from someone else's mistake, I used the wrong type of drill bit to try to drill through the metal door jamb. I ended up destroying a drill bit in the process. (And having to make another trip to the workshop.)
• You can use the cardboard that the door came in to clean up your mess.  All the parts of the other door went onto that box, which I dragged out to the garage.

This was a simple project for the average DIYer.  I think we have really improved the look and functionality of our master bathroom with the new shower door.